Helium leak testing
What is helium leak testing?
Helium is used to find small leaks or possibly larger leaks in bigger volumes. The helium is used as a tracer gas and its concentration is measured.
Why use helium for leak testing?
Helium is one of the smallest gas molecules and is inert. Being inert it is relatively safe to use (rather than hydrogen) and will not react with any of the materials within the part to be tested. In most helium leak testing applications, one uses a mass spectrometer tuned to detect helium although it is possible to use a residual gas analyser. Helium leak testing can generally be between one thousand and one million times more sensitive than using pressure decay techniques.
What are the benefits of Helium Leak Testing?
Using this technique you can leak test to find smaller leaks than with other test processes, using a temperature stable, dry technique. This should result in a longer product life. There are two basic techniques;
- High vacuum testing which allows leak test thresholds to be set down as low as 1x10-12 mbar.l.sec-1
- Sniffing which is generally used for helium leaks down to 1x10-6 mbar.l.sec-1. For reference 1 cubic millimetre per second is approximately 1x10-3 mbar.l.sec-1.
Most tests use readily available Balloon Gas. On rare occasions certifiably pure gas is used. On a safety note, please remember that helium contains no oxygen and is therefore an asphyxiant. It is worth remembering that leakage is a flow of fluid from a higher pressure to a lower pressure through a fault in an assembly or manufactured part.
The high vacuum technique requires that the test volume to which the instrument is connected is at high vacuum i.e. less than 10mbar absolute pressure. Can the part or assembly withstand this pressure? It is possible to test a part at high pressure and high vacuum at the same time. You need to arrange these pressures either side of the leaking boundary. This may mean putting the part under test inside a leak tight chamber.
When testing using helium it is possible to flood the mass spectrometer with helium if there is a large leak. In most instances, where there are many minutes between each test, this is not a problem, one just waits for the instrument to clean itself up. One can also either sniff or spray helium. Sniffing is used where the part can be pressurised above atmospheric and a sniffing gun is manually positioned round the part. Spraying is where the part can be evacuated and helium is manually sprayed over the outside of the part.
Background Helium concentration.
Helium can and will get everywhere if it can. It gets quite difficult sometimes to determine where the helium is coming from.
There is approximately 5 ppm Helium in the atmosphere. If the part under test is filled with helium it is important that the test charge is taken away and not just released into the immediate area. For just a few tests, the helium can be diluted in the immediate area. For more frequent testing, this may mean piping the extracted test gas away to the outside of the building on the downwind side and well clear from doors or windows that could allow it back in.
To locate helium leaks one usually either sprays or sniffs, the latter being the norm in high volume testing. When sniffing one starts with 5 ppm and would usually look to detect an increase of a further 5 ppm.
One can use this detectable rise in helium concentration to test parts inside a shroud where the test pressure is at or near atmospheric pressure. By circulating the air within the shroud and passing it by a mass spectrometer in sniffing mode, you can set an alarm limit at say 8ppm. Again it is important to flush or extract away any contaminated air once the test has completed.
Helium leak testing at Lower Limits
When testing at 1 x10-9 and below one may need to do additional things to be able to complete a viable test. One may need to purge away and clinging helium left in the part to be tested or the test chamber. For example, with the chamber and part open to atmosphere before the test, they are exposed to a helium concentration of 5 ppm. The helium can cling to various surfaces and affect the results of the test. So, one may need to "wash" away any clinging helium in the chamber and part in a gas containing no helium. The sequence might be:
- evacuate both the part and chamber
- back fill the test volume with certified clean dry nitrogen
- fill the part with the test gas
Helium leak testing at high production rates.
When high volume production requires high vacuum, you must also consider the time taken to pump down to the required level of vacuum, this can be significant.
At higher production rates, having much shorter time to test a part, large leakers may be a problem. The flooding of the leak test instrument with helium may take several minutes for the helium to reduce to a level where testing can recommence. To reduce the effect of a large leaker one can; build up to the full test pressure in stages, build up to the full concentration, flush the mass spec with a gas with no helium present or pre-screen using an air decay technique before helium testing. Air decay pre-screening will allow known larger leakers to be to be removed prior to helium leak testing.
When testing at high speed it is important to reduce the test time to its minimum. To do this one may have to employ a number of techniques to; reduce the test volume (by infilling voids and ensuring minimum pipe run volumes), nitrogen flush, etc. Of course at high speed the automatic handling of the product and automatic connection play a large part.
Tooling & Pipework
If one is intending to helium leak test a part it is important to note that the tooling and pipework used to create the test volume and helium gas supply must be leak tight to higher degree than the leak test threshold. This means that careful engineering of the seals is necessary, particularly where complicated seals are required (e.g. right angled seals for 2 perpendicular faces).
One must also use helium leak tight valves and pipework and pay particular attention to the sizing of the vacuum pipework
Helium mixing, helium recovery and helium re-use
When testing large volumes, at higher pressures and at high speed, the quantity of helium being used may become significant. There are a number of techniques to reduce the consumption of the helium gas.
- Mix the helium with another lower cost gas either nitrogen or compressed air. This is only possible where the sensitivity of the test is not compromised by the mixing process.
- Re-use the gas from one test by extracting it from the device and then pushing it into the next device. This can often be implemented by a combination of a vacuum pump and simple air cylinder arrangement if the volume is not too large. Between cycles it is possible to use the mass spectrometer to monitor the concentration of helium that is being re-used; when the concentration falls below an acceptable level it is dumped and a new charge of helium is used.
- Helium recovery; here one extracts the helium into an intermediate holding vessel to be compressed back to high pressure to recover the helium.